Brainboxes PX-246 Spezifikationen Seite 52
- Seite / 82
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Operation
52
6 OPERATION
6.1 CONTROL
Control of the module is via push buttons mounted on the front of the module with
START INHIBIT/RESET
( )
, MANUAL
( )
, AUTO
( )
, MODE
( )
, ALARM MUTE
( ),
LATEST TRANSFER INFORMATION
( ),
CLOSE/OPEN S1
( )
and CLOSE/OPEN S2
( )
functions. For normal operation, these are the only controls which need to be operated. The smaller
push buttons are used to access further information such as mains voltage or to change the state of
the load switching devices when in manual mode. Details of their operation are provided later in this
document.
The following descriptions detail the sequences followed by a module containing the standard ‘factory
configuration’. Always refer to your configuration source for the exact sequences and timers observed
by any particular module in the field.
CAUTION:
CAUTION: CAUTION:
CAUTION: -
--
-
The module may instruct an engine start event due to external influences.
The module may instruct an engine start event due to external influences. The module may instruct an engine start event due to external influences.
The module may instruct an engine start event due to external influences.
Therefore, it
Therefore, itTherefore, it
Therefore, it
is possible for the engine to start at any time without warning. Prior to
is possible for the engine to start at any time without warning. Prior to is possible for the engine to start at any time without warning. Prior to
is possible for the engine to start at any time without warning. Prior to
performing any maintenance on the system, it is recommended that steps are taken to
performing any maintenance on the system, it is recommended that steps are taken to performing any maintenance on the system, it is recommended that steps are taken to
performing any maintenance on the system, it is recommended that steps are taken to
remove the battery and isolate supplies.
remove the battery and isolate supplies.remove the battery and isolate supplies.
remove the battery and isolate supplies.
NOTE:
NOTE: NOTE:
NOTE: -
--
-
This control
This controlThis control
This control
module
modulemodule
module
has PLC functionality buil
has PLC functionality builhas PLC functionality buil
has PLC functionality built in.
t in.t in.
t in.
This can have change the
This can have change the This can have change the
This can have change the
standard operation when used.
standard operation when used.standard operation when used.
standard operation when used.
(
((
(Default configuration the no PLC is set. See software
Default configuration the no PLC is set. See software Default configuration the no PLC is set. See software
Default configuration the no PLC is set. See software
manual for more information)
manual for more information)manual for more information)
manual for more information)
- DEEP SEA ELECTRONICS PLC 1
- TABLE OF CONTENTS 3
- 1 BIBLIOGRAPHY 6
- 2 INTRODUCTION 7
- 3 SPECIFICATIONS 8
- 3.2 TERMINAL SPECIFICATION 9
- 3.5 LOAD CURRENT SENSING 10
- 3.5.2 CT POLARITY 11
- 3.5.3 CT PHASING 11
- 3.5.4 CT CLASS 11
- 3.6 DIGITAL INPUTS 12
- 3.7 OUTPUTS 12
- 3.8 COMMUNICATION PORTS 13
- 3.8.2 RS232 14
- 3.8.3 RS485 16
- 3.10.1 DIMENSIONS 18
- 3.10.2 PANEL CUTOUT 18
- 3.10.3 WEIGHT 18
- 3.10.4 FIXING CLIPS 19
- 3.11 APPLICABLE STANDARDS 21
- 4 INSTALLATION 25
- 4.1.6 S1 VOLTAGE SENSING 28
- (I1,I2,I3) 29
- 4.1.10 RS485 CONNECTOR 31
- 4.1.11 RS232 CONNECTOR 31
- 4.3 ALTERNATIVE TOPOLOGIES 34
- 4.4 EARTH SYSTEMS 39
- 5 DESCRIPTION OF CONTROLS 40
- 5.2 QUICKSTART GUIDE 41
- 5.3.1 STATUS 43
- 5.3.2 S1 44
- 5.3.3 S2 44
- 5.3.4 EXPANSION 44
- 5.3.5 ALARMS 44
- 5.3.6 EVENT LOG 45
- 5.3.7 SERIAL PORT 46
- 5.3.8 SCHEDULER 50
- 5.3.9 ABOUT 50
- 6.1 CONTROL 52
- 6.2 CONTROL PUSH-BUTTONS 53
- 6.3 LOAD SHEDDING CONTROL 55
- 6.4 START INHIBIT/RESET 56
- 6.5 MANUAL MODE 57
- 6.5.3 STOPPING SEQUENCE 58
- 6.6 AUTOMATIC MODE 59
- 6.6.3 S2 AVAILABLE 60
- 6.6.4 STOPPING SEQUENCE 60
- 6.7 MODE SELECTION 61
- 6.7.2 TEST OFF LOAD 62
- 6.7.3 PROHIBIT RETURN 63
- 7 PROTECTIONS 65
- 7.1 INDICATIONS 66
- 7.2 WARNINGS 67
- 7.3 ELECTRICAL TRIPS 68
- 8.1 STOP MODE 69
- 8.2 MANUAL MODE 69
- 8.3 AUTO MODE 69
- 9.1.1 EDITING A PARAMETER 72
- 9.2 ADJUSTABLE PARAMETERS 73
- 10 COMMISSIONING 75
- 11 FAULT FINDING 76
- 11.4 COMMUNICATIONS 77
- 11.5 INSTRUMENTS 77
- 11.6 MISCELLANEOUS 78
- 12.1.1 PACK OF PLUGS 79
- 12.1.2 INDIVIDUAL PLUGS 79
- 13 WARRANTY 81
- 14 DISPOSAL 81
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern